GND
A115x
VCC
V+
0.01 糉
A
GND
ECU
Package UA Only
A
R
SENSE
C
BYP
GND
A115x
VCC
V+
0.01 糉
A
GND
R
SENSE
C
BYP
Figure 2. Typical application circuits
(A) Low side sensing
(B) High side sensing
Amp
Regulator
Clock/Logic
Hall Element
Low-Pass
Filter
Chopper Stabilization Technique
When using Hall-effect technology, a limiting factor for
switchpoint accuracy is the small signal voltage developed
across the Hall element. This voltage is disproportionally small
relative to the offset that can be produced at the output of the
Hall sensor IC. This makes it difficult to process the signal while
maintaining an accurate, reliable output over the specified oper-
ating temperature and voltage ranges. Chopper stabilization is
a unique approach used to minimize Hall offset on the chip. The
patented Allegro technique, namely Dynamic Quadrature Offset
Cancellation, removes key sources of the output drift induced by
thermal and mechanical stresses. This offset reduction technique
is based on a signal modulation-demodulation process. The
undesired offset signal is separated from the magnetic field-
induced signal in the frequency domain, through modulation.
The subsequent demodulation acts as a modulation process for
the offset, causing the magnetic field-induced signal to recover
its original spectrum at base band, while the DC offset becomes
a high-frequency signal. The magnetic-sourced signal then can
pass through a low-pass filter, while the modulated DC offset is
suppressed. The chopper stabilization technique uses a 350 kHz
high frequency clock. For demodulation process, a sample and
hold technique is used, where the sampling is performed at twice
the chopper frequency. This high-frequency operation allows
a greater sampling rate, which results in higher accuracy and
faster signal-processing capability. This approach desensitizes
the chip to the effects of thermal and mechanical stresses, and
produces devices that have extremely stable quiescent Hall out-
put voltages and precise recoverability after temperature cycling.
This technique is made possible through the use of a BiCMOS
process, which allows the use of low-offset, low-noise amplifiers
in combination with high-density logic integration and sample-
and-hold circuits.
Figure 3. Chopper stabilization circuit (Dynamic Quadrature Offset Cancellation)
Chopper-Stabilized, Two Wire
Hall-Effect Switches
A1150, A1152, A1153, A1155,
A1156, A1157, and A1158
8
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
A1180LUA-T
IC SWITCH HALL EFFECT UNI 3-SIP
A1184LUA-T
IC SWITCH HALL EFFECT UNI 3-SIP
A1186LUA-T
IC SWITCH HALL EFFECT UNI 3-SIP
A1193LUA-T
IC SW HALL EFFECT CHOPPER 3SIP
A1203LUA-T
IC SW CONTINUOUS TIME BIPO 3-SIP
A1205EUA-T
IC SWITCH HALL EFFECT GP 3-SIP
A1211LUA-T
IC LATCH HALL EFFECT 3-SIP
A1220LUA-T
IC HALL EFFECT LATCH 3V 3-SIP
相关代理商/技术参数
A1155LUBTN-F-T
功能描述:2WIRE FACTORY PROGRAMMED SWITCH 制造商:allegro microsystems, llc 系列:汽车级，AEC-Q100 零件状态:在售 功能:单极开关 技术:霍尔效应 极化:南极 测试条件:-40°C ~ 150°C 电压 - 电源:3 V ~ 24 V 电流 - 电源（最大值）:17mA 电流 - 输出（最大值）:- 输出类型:电流源 特性:- 工作温度:-40°C ~ 150°C 封装/外壳:2-SIP 模块 供应商器件封装:2-ultramini SIP 标准包装:8,000
A1155LUBTN-T
功能描述:2-WIRE FACTORY PROGRAMMED SWITCH 制造商:allegro microsystems, llc 系列:汽车级，AEC-Q100 零件状态:在售 功能:单极开关 技术:霍尔效应 极化:南极 感应范围:6mT 跳闸，1mT 释放 测试条件:-40°C ~ 150°C 电压 - 电源:3 V ~ 24 V 电流 - 电源（最大值）:17mA 电流 - 输出（最大值）:- 输出类型:电流源 特性:- 工作温度:-40°C ~ 150°C 封装/外壳:2-SIP 模块 供应商器件封装:2-ultramini SIP 标准包装:8,000
A1156
制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Chopper-Stabilized, Two Wire Hall-Effect Switches
A-1156
制造商:TE Connectivity 功能描述:
A1156LLHLT-T
功能描述:IC HALL EFFECT SWITCH SOT-23-W RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
A1156LLHLX-T
功能描述:IC SWITCH HALL EFFECT UNI SOT-23 RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
A1156LUA-T
功能描述:IC SW HALL EFFECT CHOPPER 3SIP RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
A1156LUBTN-F-T
功能描述:IC HALL EFFECT SWITCH 2SIP 制造商:allegro microsystems, llc 系列:- 包装:- 零件状态:有效 功能:单极开关 技术:霍尔效应 极化:南极 感应范围:6mT 跳闸，1mT 释放 测试条件:-40°C ~ 150°C 电压 - 电源:3 V ~ 24 V 电流 - 电源（最大值）:17mA 电流 - 输出（最大值）:- 输出类型:开路漏极 特性:- 工作温度:-40°C ~ 150°C（TA） 封装/外壳:- 供应商器件封装:- 标准包装:4,000